Je hebt nog geen producten in je winkelwagen.
reTerminal E10-1 - Expansion Board
Omschrijving
De reTerminal E10-1 is een uitbreidingskaart voor de reTerminal die oplaadbare en draagbare functies, verbeterde draadloze communicatie en industriële datatransmissie mogelijk maakt, samen met audiomogelijkheden. Het zorgt ervoor dat de reTerminal nog krachtiger wordt en kan worden ingezet in meer scenario's, zoals snelle industriële en landbouwtoepassingen, of verbeterde draadloze thuis- en individuele toepassingen.
Kenmerken
- Alternatieve oplaadmodi: Voeding door UPS-18650 tweevoudige oplaadbare batterij, DC-aansluiting en PoE-functie
- Veelvoudige Draadloze Communicatie: Biedt LoRaWAN/LTE/4G/5G alle vier datatransmissiecapaciteiten met antennes
- Industriële interface aan boord: Ondersteunt RS-485, RS-232, en CAN Bus hoge snelheidsverbinding
- Extra opslag aan boord: Beschikbare kaartsleuf ter ondersteuning van SSD met M.2 B KEY, SATA 2.0
- Audio mogelijkheden aan boord: Uitgerust met twee microfoons en een luidspreker voor uitbreidbare Al-powered mogelijkheden
Met de reTerminal E10-1 kun je meer edge computing toepassingen ontwikkelen en implementeren met behulp van de reTerminal, de interfacefaciliteit die door Seeed wordt aangeboden. Met meerdere bridge-IC's en hoogwaardige randapparatuur geeft dit bord de reTerminal de kracht van oplaadbare en draagbare functies, verbeterde draadloze communicatie en industriële datatransmissie, samen met audiomogelijkheden.
De reTerminal E10-1 is een uitbreidingskaart en volledig compatibel met de reTerminal, waar ze eenvoudig kunnen worden aangesloten via de industriële high-speed signaalconnector midden op de kaart. Hij past de laad-ontlaadfunctie toe voor de reTerminal door de UPS-18650 tweevoudige oplaadbare batterij te gebruiken en de DC jack power interface aan te sluiten. Verder is er een Power over Ethernet (POE) module op de printplaat aangebracht, zodat de reTerminal E10-1 ook kan worden opgeladen via de Gigabit Ethernet RJ45 connector.
Het bord ondersteunt de reTerminal bij het verzenden van gegevens via de industriële interface zoals DB9 Connector voor RS-232 en geïntegreerde 6 Pin Terminal Connector voor RS485 en CAN. Ondertussen zijn er multifunctionele mini-PCIe en M.2 B Key connectoren op het bord, die de reTerminal helpen om LoRaWAN en LTE draadloze functie en SSD opslagcapaciteit toe te voegen. Daarnaast is er ook een connector aan boord een 4G/5G communicatie module.
De reTerminal E10-1, met dubbele analoge microfoons en een luidspreker, maakt gebruik van de audiomogelijkheden van de reTerminal, waardoor de reTerminal in meer situaties kan worden ingezet, zoals bij industriële hogesnelheidstoepassingen, landbouwtoepassingen of verbeterde draadloze toepassingen thuis, voor individueel gebruik. Door de mogelijkheden op de printplaat te benutten, kan de reTerminal in oneindig veel toepassingen worden ingezet, zoals het aansluiten van LoRaWAN-apparaten voor lange afstands communicatie in de landbouw of het aansluiten van mmWave-radarapparaten voor gezondheidszorg in huis.
Toepassingen
- Industrieel: Machinebewaking, veiligheidsalarm, gegevensoverdracht en -opslag op industrieel niveau.
- Landbouw: Gewasbewaking, insectenalarm, LoRa/LTE/5G draadloze communicatie
- Thuis: Huisbewaking, veiligheidsalarm, gesteunde uitschakeling
- Individueel: Mobiel-mens-machine-interactiecomputer
Hardware Overzicht
Specificaties
Power | DC Jack | Supply power to the reTerminal, the expansion board and the battery in DC 12V @4A | The DC Jack or PoE power supply should be prioritized. If the input power exceeds 15.6V, it will enter the input overvoltage protection state. |
PoE | The PoE power input is RJ45 and supports a maximum of 25W power input. | ||
UPS - 18650 battery | 2x battery holder with fixed pin. During the charging process, the battery will automatically stop charging if it overheats, and LED 2 will flash the alarm. | ||
External I/O | RS-485 Interface | RS-485 supports a maximum communication rate of 256000 baud | Support automatic sending and receiving |
RS-232 Interface | RS-232 supports a maximum communication rate of 256000 baud | ||
CAN | CAN at common-mode supports a 500KBps communication rate, CAN at FD mode supports the communication rate up to 8Mbps | ||
Antenna interface | Equip four antennas | ||
RJ45 Interface for Giga Ethernet | Equip LAN7800 IC with the RJ45 interface and support PoE module | Ethernet supports maximum gigabit rates, but the LAN7800 driver is required | |
DC jack Power interface | DC 12V @4A | ||
100 pins Industrial High-Speed Interface | Connect with reTerminal through 100 pins high-speed interface | ||
Internal I/O | M.2 Interface | Support SSD, M.2 B KEY driver, USB3.0 GEN1 and SATA 2, suitable for 2242/2280 | Compatible with B key SSD |
Mini-PCIe | Support UART, USB2.0, I2C, and SPI communication modes | Compatible with WM1302 SPI and WM1302 USB | |
SIM card slot | Insert the LTE/4G/5G sim card | The SIM card only supports mini-pcie or M.2 devices at one time and it can be toggled by the swith on the board | |
Microphone | Two Analog Microphones | ||
Speaker | 8Ω/1W | ||
Fan | 3 Pin Fan | Support speed control and speed measurement | |
Network | Wireless Connection | M.2 Interface Support 4G/5G wireless modules | Compatible with SIMCOM 8052 5G |
Mini-PCIe Support LTE/4G/LoRaWAN modules | Compatible with EC25/EC20, LoRaWAN module suggsted Seeed WM1302 | ||
SIM card slot Insert the LTE/4G/5G Sim card | The SIM card only supports mini-pcie or M.2 devices at one time and it can be toggled by the switch on the board | ||
Antenna interface | Equip four antennas | ||
Giga Ethernet | Equip LAN7800 IC with the RJ45 interface and support PoE module | Ethernet supports maximum gigabit rates, but the LAN7800 driver is required | |
Display | LED1 | DC Jack Power status indicator | |
LED2 | LED 2, as the battery status indicator, blinks during the reTerminal startup, and stops blinking after done loading the battery driver. At this time, if the battery is at the charging state, LED 2 will stay lighting, otherwise the LED 2 will be off. | ||
LED3 | User LED |
Accessoire Informatie
Houd er rekening mee dat de onderstaande accessoires niet in het pakket zitten. We geven de informatie hier om je te helpen de juiste accessoires te kiezen.
Note | Product Name | Remarks |
Power cable | DC 12V @4A | Full power consumption requires a 4A power supply, but sometimes partial 2A/3A power supply can also support |
Battery | 18650 | Panasonic NCR18650B 3.6V 3400mAh recommended |
SSD | M.2 SSD 2242/2280 | M.2 B key (SATA) |
4G module | EC25/EC20 | Tested with Quectel (manufacturer) |
5G module | SIM8202G | Tested with Simcom (manufacturer) |
Wio Module | WM1302 LoRaWAN Gateway Module (USB/SPI) US/EU | WM1302 LoRaWAN Gateway Module |
Reviews
- 1 stuk(s) direct uit voorraad leverbaar
- Voor 17:00 uur besteld, is vandaag verzonden
- Verzonden vanaf € 46,52 naar Verenigde Staten
- 30 dagen niet goed, geld terug
- Snelle levering vanuit Nederland
Documentatie
Pakket Inhoud
- 1x reTerminal E10-1 - Expansion Board
- 1x Screw Driver
Specificaties
Algemeen | |
Productcode | SS-103060001 |
Merk | Seeed Studio |
MPN | 103060001 |