Arduino Motor Shield Rev3

Arduino Motor Shield Rev3
Arduino Motor Shield Rev3
Arduino Motor Shield Rev3
Arduino Motor Shield Rev3
Arduino Motor Shield Rev3
Arduino Motor Shield Rev3
Arduino Motor Shield Rev3
Arduino Motor Shield Rev3

Description

The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.

Power

The Arduino Motor Shield must be powered only by an external power supply. Because the L298 IC mounted on the shield has two separate power connections, one for the logic and one for the motor supply driver. The required motor current often exceeds the maximum USB current rating. External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the Arduino's board power jack on which the motor shield is mounted or by connecting the wires that lead the power supply to the Vin and GND screw terminals, taking care to respect the polarities. To avoid possible damage to the Arduino board on which the shield is mounted, we reccomend using an external power supply that provides a voltage between 7 and 12V. If your motor require more than 9V we recommend that you separate the power lines of the shield and the Arduino board on which the shield is mounted. This is possible by cutting the "Vin Connect" jumper placed on the back side of the shield. The absolute limit for the Vin at the screw terminals is 18V.

The power pins are as follows:

  • Vin on the screw terminal block, is the input voltage to the motor connected to the shield. An external power supply connected to this pin also provide power to the Arduino board on which is mounted. By cutting the "Vin Connect" jumper you make this a dedicated power line for the motor.
  •  GND Ground on the screw terminal block.

The shield can supply 2 amperes per channel, for a total of 4 amperes maximum.

Connections

Brushed DC motor. You can drive two Brushed DC motors by connecting the two wires of each one in the (+) and (-) screw terminals for each channel A and B. In this way you can control its direction by setting HIGH or LOW the DIR A and DIR B pins, you can control the speed by varying the PWM A and PWM B duty cycle values. The Brake A and Brake B pins, if set HIGH, will effectively brake the DC motors rather than let them slow down by cutting the power. You can measure the current going through the DC motor by reading the SNS0 and SNS1 pins. On each channel will be a voltage proportional to the measured current, which can be read as a normal analog input, through the function analogRead() on the analog input A0 and A1. For your convenience it is calibrated to be 3.3V when the channel is delivering its maximum possible current, that is 2A.

If you don't need the Brake and the Current Sensing and you also need more pins for your application you can disable this features by cutting the respective jumpers on the back side of the shield. The additional sockets on the shield are described as follow: Screw terminal to connect the motors and their power supply. 2 TinkerKit connectors for two Analog Inputs (in white), connected to A2 and A3. 2 TinkerKit connectors for two Aanlog Outputs (in orange in the middle), connected to PWM outputs on pins D5 and D6. 2 TinkerKit connectors for the TWI interface (in white with 4 pins), one for input and the other one for output.

Physical Characteristics

The maximum length and width of the Motor Shield PCB are 2.7 and 2.1 inches respectively. Four screw holes allow the board to be attached to a surface or case. Note that the distance between digital pins 7 and 8 is 160 mil (0.16"), not an even multiple of the 100 mil spacing of the other pins.

Specifications

Operating Voltage5V to 12V 
Motor controllerL298P, Drives 2 DC motors or 1 stepper motor 
Max current2A per channel or 4A max (with external power supply) 
Current sensing1.65V/A 
 Free running stop and brake function 
Functionpins per Ch. Apins per Ch. B
Direction D12D13
PWMD3D11
BrakeD9D8
Current SensingA0A1

 

Reviews

Arduino Motor Shield Rev3
Product Code: ARD-A000079
€ 24.00
Ex. VAT
10 or more € 22.80 Ea. (-5%)
3 piece(s) in stock
  • Shipped on Wednesday when ordered now.
  • Shipping from € 9.00 to United States
  • 30 days money back guarantee
  • Fast shipping from The Netherlands

Software

Download the latest Arduino IDE
The open-source Arduino Software (IDE) makes it easy to write code and upload it to the board. This software can be used with any Arduino board.

Specifications

General
Product CodeARD-A000079
BrandArduino
EAN7630049200371
MPNA000079
PlatformArduino
For use withArduino
Technical
Input Voltage12 VDC
Operating Voltage5 ~ 12 VDC
Output Current (Max)2A
Plug BScrew Terminal
Other
Dimensions80 X 60 X 35mm
Weight25g

You might like these as well

This stepper motor is good for small projects and experimenting with steppers.
€ 4.49 Ex. VAT
Run four solenoids, two DC motors or a bi-polar or uni-polar stepper at up to 600 mA per channel with the L293D.
€ 3.99 Ex. VAT
Adafruit Motor Shield to drive 4 DC motors or 2 steppermotors
€ 18.99 Ex. VAT
Fast shipping
Order before 17:00h (Mon-Fri) for same day shipping.
Money back guarantee
You have a 30-day return period on your order
Worldwide shipping
Shipped from the Netherlands using PostNL and DHL.