Adafruit Feather HUZZAH with ESP8266 WiFi

Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi
Adafruit Feather HUZZAH with ESP8266 WiFi

Description

This is the Adafruit Feather HUZZAH ESP8266 WiFi development board with built in USB and battery charging. Its an  ESP8266 WiFi module with all the extras you need, ready to rock! We also have a pre-soldered version available.

At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can progam the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. Adafruit wired up a USB-Serial chip that can upload code at a blistering 921600 baud for fast development time. It also has auto-reset so no noodling with pins and reset button pressings.

To make it easy to use for portable projects, a connector is added for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available.

Specifications

  • 51mm x 23mm x 8mm
  • 9.7g
  • ESP8266 @ 80MHz with 3.3V logic/power
  • 4MB of FLASH (32 MBit)
  • Built in WiFi 802.11 b/g/n
  • 3.3V regulator with 500mA peak current output
  • CP2104 USB-Serial converter onboard with 921600 max baudrate for uploading
  • Auto-reset support for getting into bootload mode before firmware upload
  • 9 x GPIO pins - can also be used as I2C and SPI
  • 1 x analog inputs 1.0V max
  • Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
  • Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

Content

  • Comes fully assembled and tested by Adafruit.
  • Header 

Note

Lipoly battery and USB cable not included.

Reviews

  • Ordered before 17:00, shipped today.
  • Shipping from € 8.91 to United States
  • 30 days money back guarantee
  • Fast shipping from The Netherlands

Specifications

General
Product CodeADA-2821
BrandAdafruit
MPNP2821
PlatformFeather
Technical
Input PlugMicro USB
Input Voltage3.3 ~ 5.0 VDC
Operating Voltage3.3 VDC
Other
Dimensions22.8mm x 51mm x 7.2mm
Weight6,2g

You might like these as well

ESP8266 SMT Module - ESP-12S ESP8266 SMT Module - ESP-12S
-20%
Add Internet to your next project with a bite-sized WiFi microcontroller.
€ 5.45 Ex. VAT € 6.82
Feather is the new development board from Adafruit, and like it's namesake it is thin, light, and lets you fly! This is the Feather 32u4 Basic Proto, it has a bunch of prototyping space built right in.
€ 17.77 Ex. VAT
Two Female Stacking Headers from Adafruit.
€ 1.32 Ex. VAT
Fast shipping
Order before 17:00h (Mon-Fri) for same day shipping.
Money back guarantee
You have a 30-day return period on your order
Worldwide shipping
Shipped from the Netherlands using PostNL and DHL.